0086-21-58386256
The Perfect Pair Shock Pulse and Vibration Monitoring Figure 2: The autogenous mill at the Boliden Garpenberg Mine. There are several different types of …
Fodamon engineers shares the reasons and solutions of the severe vibration of the ball mill pinion. The normal operation of the ball mill uses the motor to drive the ball mill to perform rotation operation. The motor …
Vibration Sag Mill Motor NDE Bearing. At our mine we have an issue with vibration at the Sag Motor NDE bearing. The bearing is a journal white metal bearing. The motor has …
Now, when the mill is started, vibration values are around 14 mm/s, first 4 harmonics of the GM, and then for about half an hour they go up to 28 mm/s (again 4 harmonics of GM) - in horizontal direction …
In the example below, the bearing housing of a discharge pulley of a conveyor belt presents vibration amplitudes close to 1g, with the axial axis presenting higher values. When we look closely, we can see that the peak of this signal of duration 4s corresponds to 1.1194g at time 2.52s. ... Joel Nunes, expert in vibration analysis at …
Pinion shaft bearings are of the SKF anti-friction type mounted in a common twin bearing assembly. Bearings are fixed in place so that the pinion shaft of the mill is always in alignment with the drive …
The source of the "thump" was traced to roller backlash caused by bearing wear at the transfer gear end of a particular mill. The tonal component was diagnosed as excessive vibration at the tooth mesh frequency of the pinion on another mill caused by worn teeth on the gear. The "thump" could be eliminated by replacing the bearings.
High vibrations on a ball mill. Hello everyone, I have a problem with high levels of vibration at the supports of the pinion (fixed and floating bearings) of the cement ball mill. The kinemantic scheme …
Measure, Manage and Improve Pinion misalignments, resonance, unbalance and bearing and gear meshing faults in geared Our paper outlines the efforts that have gone into adapting conventional ...
Vibration caused by the displacement of the transmission parts After the ball mill works for a long time, the anchor bolts of the motor, reducer and pinion bearing seat in the transmission part will sometimes loosen, and the transmission part will move, so that the axis is not in the same straight line, and vibration occurs.
Snoopy49 said: They probably didn't pay any attention to the service manual when they removed and replaced the drive shaft. View attachment 66641. Driveline vibration — occurs at cruising speeds. Misalignment of yellow dot on driveshaft-to-yellow dot on pinion flange plus or minus 1 bolt hole.
Vibration accelerometer, installed on pinion bearing DE 4.2 Measuring techniques Pinion bearing NDE: SPM HD Pinion bearing DE: EVAM HD ENV Filter 3 and Filter 4 4.3 Condmaster setup Settings in Condmaster Ruby 2018.2.3 are as follows. SPM HD technique Measuring time: Same as FFT measurement
Worn out pinion bearings create more whirring noise rather than rumbling because it rotates several times faster than the carrier assembly of the vehicle. Vibrations: Vibration is one of the pronounced …
When the surface of the pinion of the ball mill is found to be worn, it can be manually polished if it is not serious, so as to reduce the surface roughness of the gear and ensure the normal operation of the pinion; If badly worn …
Online Vibration Monitoring System Improves Fault Detection in a SAG Mill. A copper mine site already had an extensive condition monitoring program in place. We went through their oil analysis …
Ball mill at the Asarel Medet copper mine. Using HD measurement technologies, Bulgarian copper producer Asarel Medet AD monitors the mechanical condition of critical equipment in the open-pit mine and …
The vibration at the NDE bearing was around 2mm/sec. In the last month it has climbed to 4.5mm sec with the dominate frequency 1x RPM. it is not the level as much as we are getting this slight increase.I had the motor holding down bolts tightened and a slight reduction to 4.2mm/sec rms.
An investigation was carried out to determine the response of an existing industrial plant to rod mill vibration. The disturbing forces and frequencies of the mill were estimated and compared with ...
Pinion Shaft an overview ScienceDirect Topics. Rod Mill–Ball Mill Circuit: Consider the set-up in Example 8.1 along with the following additional data: Grindability index for the ball mill = 12.0 kWh/t. Product size from the ball mill = 150 μm. Determine the size of the ball mill operated in closed circuit. Solution Step 1.
A dynamic analysis was carried out on the existing building to determine the structural response to the new mill vibration. The soil springs, geometric damping ratios, and rocking springs were ...
That weight changed the pinion angle and created a vibration. Our quick fix on the road (because we couldn't change the pinion angle) was to raise the trans level by ¾-inch. Eventually, we determined the real problem stemmed from a sagging crossmember, causing the engine/transmission angle to achieve a 5 degree tail-down attitude.
We are experiencing high vibration on our dual drive ball mill. The high vibration is on the motor DE bearing on axial direction. Dominant frequency is girth and pinion gear mesh. See attached spectrums and trends. Gearbox hold-down bolts are breaking due to high vibration.
Reply with quote. #1. I have an issue with a gear drive on a ball mill. 2XGM is rising and i have sidebands at 107cpm and I don't know why they are at 107 (not relevant to any turning speeds ect.) I checked the root clearance a week ago and the inboard is about a .066 smaller than the outboard. The pinion is 24" long and has 24 teeth.
we have been having problems with mill motor bearings vibration. An induction motor drives reduction gear box, and in the output drives a pinion. The pinion drives the girth wheel on the mill. The pinion and the gearbox are coupled through a pneumatic clutch.
VIBRATION STUDIES OF CEMENT MILL Steps for vibration measurements Impact test was carried out at selected locations on the torsion bar to know its natural frequency …
Worn out pinion bearings create more whirring noise rather than rumbling because it rotates several times faster than the carrier assembly of the vehicle. Vibrations: Vibration is one of the pronounced …
Pinion bearing damage in ball mill Ball mill at the Asarel Medet copper mine. Pinion bearing damage in ball mill Using HD measurement technologies, Bulgarian copper producer Asarel Medet AD monitors the mechanical …