0086-21-58386256
The bulk density is more in compacted state as compared to the loose which shows that the bulk density greatly depends on the degree of compaction or how densely it is packed.; Usually increase in bulk density should be above 15% for coarse aggregate and should be below 15% for fine aggregate, But in our results it is 11.20% for fine aggregate and 11.48% for coarse aggregate.
Rooded bulk density = Net compacted wt/Volume. Rooded bulk density = 23.93 kg/15 L. Rooded bulk density = 1.595 Kg/L. % of voids present in coarse aggregates. Voids :- the space between the coarse particles of aggregate which was not occupied by solid …
Jul 16, 2017· For this test procedure, it is sufficiently accurate to accept the density of water at room temperature to be 998 kg/m 3. Rodding the aggregates: Fill the bucket one third full and rod the aggregate layer with 25 strokes of the tamping rod, evenly distributed over the surface.
Jul 30, 2012· If a statement is like: A coarse aggregates with higher bulk density, then it means few of the voids can be filled by using fine aggregates and cement. For testing, British Standard (BS 812) has specified the degree of compaction. These are; Loose ( Un-compacted) Compacted; The test will be carried out by using metal cylinder having prescribed depth and diameter and the bulk density is to …
Near about 35% volume of the concrete is comprised of sand. For concrete to be of good quality it should be produced by careful mixing of cement, fine and coarse aggregates, water, and admixtures as needed in order to obtain optimum quality and economy.. Natural sand i.e. locally available River sand having a bulk density of 1.71 kg/m3 was used for the construction (specific gravity is 2.65).
Corn, Chops (Coarse) 42 673 Corn, Chops (Fine) 38 609 Corn, Chops (Medium) 40 641 Corn, Cracked (Coarse) 40 641 Corn, Ground 35 561 Corn, Hominy Feed 27 433 Corn, Kibbled 21 336 Cottonseed Cake 42 673 Cottonseed Delinted 30 481 Cottonseed Flour 56 897 ... Bulk Density Chart
The bulk density and void percentage of aggregate can be evaluated using standard test methods of applicable codes such as ASTM C 29/C29M-17a, IS: 2386 (Part 3) – 1963, or BS 812-2:1995. The procedure provided in this article is based on the specification of ASTM standard ( …
Transcribed image text: Bulk density of coarse aggregate mass of the measure plus its content (kg) mass of the measure alone (kg) Loose 10.55 3.5 Compacted 11.65 3.5 480 g. Specific gravity and absorption capacity of Fine Aggregate weight of oven dry specimen in air weight of pycnometer filled with calibration mark weight of saturated surface dry specimen weight of pycnometer with specimen and ...
Apr 10, 2020· Bulk Density = Bulk Specific Gravity x 1000 kg/m 3. Bulk density of both fine and coarse normal aggregates varies within the range of 1450 to 1750 kg/m 3 (90 to 110 lb/ft 3) Bulk density is used when aggregate is to be batched by volume to convert quantities by mass to quantities by volume; Bulk density depends on how densely the aggregate is ...
The surface area of coarse aggregate is less than fine aggregates. 6: Function in Concrete: The voids between the coarse aggregate are filled up by fine aggregate. Coarse aggregate acts as inert filler material for concrete. 7: Uses: Fine aggregates are used in mortar, plaster, concrete, filling of road pavement layers, etc.
C29/C29M Test Method for Bulk Density (Unit Weight) and Voids in Aggregate. C125 Terminology Relating to Concrete and Concrete Aggregates. C128 Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate. C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates
Rooded bulk density = Net compacted wt/Volume. Rooded bulk density = 23.93 kg/15 L. Rooded bulk density = 1.595 Kg/L. % of voids present in coarse aggregates. Voids :- the space between the coarse particles of aggregate which was not occupied by solid material that is known as voids.
Dec 18, 2019· 1. Subject: Concrete technology (3350602) Topic: Bulk density and bulking of fine and coarse aggregate. Prepared by :Bhavesh Hathila 2. Index 1. Introduction 2. Bulk density 3. Bulking of fine aggregate 3. The bulk density or unit weight of an aggregate is defined as mass of the aggregate …
ANSWER 2. Calculate bulk density using the formula given. 3. Calculate percentage of void using the formula given. 4. Compare the result of each weight. 4.2 Conclusion Relation of coarse aggregate between low or high bulk density with weight and pore/void in concrete.
Bulk density also indicates the compactive effort required to compact the concrete. Related Theory: Bulk Density. It is the mass of the unit volume of bulk aggregate material. The term volume includes the volume of the individual particles and the volume of the voids between the particles.Bulk density is used in weight and volume batching. Voids
Bulk density Mix design calculations; ASTM C 29 (AASHTO T 19) Compact weight and (unit weight) classification loose weight Relative density Mix design calculations ASTM C 127 (AASHTO T 85) — (specific gravity) fine aggregate ASTM C 128 (AASHTO T 84) coarse aggregate Absorption and surface Control of concrete quality ASTM C 70 —
1. Aggregates: Bulk Density, Specific Gravity and Voids. 2. Aggregates: Limiting Values of Mechanical Properties. 3. Approximate Water Absorption of Aggregates, by Weight. Note: The coarser the aggregate, the less free water it carries. 4. Limits of Deleterious Materials (Percentage by …
Jun 14, 2021· Aggregate Bulk Density. Bulk density of aggregate is defined as the weight or mass of aggregate per unit volume. Weight aggregate in a specified volume of the container. Hence, Bulk density = Weight (Mass) / volume. It can also be explained as if 1 is the volume of aggregate, then its Bulk density = Mass. Unit- kg/m3 or lb/ft3.
Jun 24, 2013· THE DETERMINATION OF THE BULK DENSITY OF COARSE AND FINE … The bulk compacted and uncompacted density of an aggregate as defined below … A scale to weigh up to 100 kg, accurate to 0,1 kg for material + 4,75 mm. … Calculate the compacted or uncompacted bulk density to the nearest 10 kg/m3 as … »More detailed
Oct 10, 2015· For this test procedure it is sufficiently accurate to accept the density of water at room temperature to be 998 kg/m 3 (62.3 lb/ft3). Rodding the aggregates. Fill the bucket one-third full and rod the aggregate layer with 25 strokes of the tamping rod, evenly distributed over the surface.
Determine the bulk density ("unit weight") of the coarse aggregate. Report your answer to two decimal places and include the units in your answer. Volume of measure, (ft) 0.25 Weight of measure (lb) 6.10 Weight of measure + aggregate (lb) 32.70 The bulk density ("unit weight") of the coarse aggregate=
Feb 14, 2020· For a coarse aggregate, a higher bulk density means that there are few voids which are to be filled by the fine aggregate and cement. Thus, bulk density also depends upon the degree of packing. Procedure: Note down the dimensions and empty weight of the measuring container and compute its volume.
To calculate voids between particles in fine, coarse or mixed aggregates based on the same determination DISCUSSION This method is used to determine the bulk density of given specimen during the concrete mix design when the aggregate is to be batched by volume or by weight.
Essential Points. Most of the aggregates possess a relative density within 2.4 – 2.9 with a similar particle density about 2400-2900 Kg/m 3 (150-181 lb/ft 3).; Hereabouts, for coarse aggregates, the standard test process has been described in ASTM C 127(AASHTO), and for fine aggregates, the standard test practice has been described in ASTM C 128 (AASHTO).
The specific gravity may be expressed as bulk oven dry (O.D.) specific ... 1.5 When the specific gravity and absorption of the fine aggregate and the coarse aggregate are known, the combined aggregate specific gravity and absorption is determined, …
Jan 09, 2015· Objective Determination of unit weight or bulk density and void of aggregates. Equipments Name Capacity 1. Balance Sensitive to 0.5% of weight of material 2. Cylindrical metal measure Of 3 litre capacity (for fine aggregate) Of 15 litre capacity (for aggregate upto 40mm) 3. Tamping rod 16 mm dia. and 60 cm long Sample Preparation […]
The reason for using a mixture of fine and coarse aggregate is that by combining them in the correct proportions, concrete with very few voids or spaces can be made, and this reduces the amount of comparatively expensive cement needed to produce strong concrete. Density of aggregate in kg/m3. Bulk Density of the Aggregate
Feb 04, 2021· Coarse aggregate is also described by its bulk density, which is a property that can easily be tested in the laboratory. The standard testing procedure for …